BPM4100 module registers

Hardware: BPM4100

Registers are 16 bit width. 32-bit and 64-bit data is packed as following:

Register I/O

Reg 0x40, Control, R/W

• bit 0-11 unused

• bit 12 - disable 0xFEFE address decode new

• bit 13 - toggle 0 to 1 causes thermometer reset and ID reread
• bit 14 - trigger mastering enable(sending through diffpairs)
• bit 15 - run enable

Reg 0x42, Setup, RO

• bit 15-8 - device id (0xB7)

• bit 7-0 = reserved (0)

Reg 0x50, 64-bit Board Serial Number (DS18B20), RO

Reg 0x54, current temperature, RO

Reg 0x55, reserved, RO

Reg 0x56, 16-bit, firmware version number, RO

Reg 0x57, 16-bit, firmware revision number, RO

Reg 0x58 ... 5D, Link statistics, RO

• 0x58 - link error 1 (T)
• 0x59 - link error 2 (R)
• 0x5A - link error 3 (O)
• 0x5B - CRC error 1 (T)
• 0x5C - CRC error 2 (R)
• 0x5D - CRC error 3 (O)

Reg 0x60 - Run status , RO

• bit 0(lsb) - SPILL wait state
• bit 1 - SPILL state
• bit 2 - RAM Full
• bit 3 - timeout SPILL end
• bit 4-15 - unused

Reg 0x61 - Link status, RO

• bit 0 - no_clock (R)
• bit 1 - disconnected (R)
• bit 2 - *LCF timeout (R)
• bit 3 - *remote error (R)
• bit 4 - reserved
• bit 5 - no_clock (T)
• bit 6 - disconnected (T)
• bit 7 - *LCF timeout (T)
• bit 8 - *remote error (T)
• bit 9 - reserved
• bit 10 - no_clock (O)
• bit 11 - disconnected (O)
• bit 12 - *LCF timeout (O)
• bit 13 - *remote error (O)
• bit 14 - reserved
• bit 15 - reserved

Reg 0x62 - 32bit SPILL wait register, 20ns step, R/W

Reg 0x64 - 32bit SPILL length register, 20ns step, R/W

Reg 0x66 - 32bit Sample count*2 register, R/W

Reg 0x68 - Trig counter register (run enable bit clears counter), RO

Reg 0x6A - Enable mask for Table-based trigger registers(0x80..0x9F regs), R/W

Reg 0x6C - 32bit Timer trigger period register, 20ns step, R/W

Reg 0x6E - SPTRCTRL, Spill and Trigger Control register, R/W

• bit 0 - Timer Trig enable
• bit 1 - Table Trig enable
• bit 2 - EXT Trig enable
• bit 3 - NCU by B0 enable
• bit 4 - NCU by Ext enable
• bits 15:5 - unused

Reg 0x6F - TESTREG

• bit 0 - test ncu
• bit 1 - test trig
• bit 2 - test trig counter enable (see also regs 0x6C, 0x6E)
• bit 3 - enable 12.5 MHz on NIM1 and 6.25 MHz on NIM2 outputs
• bit 4-12 unused
• bit 13 - reset timer trigger counter after spill_wait
• bit 14 - select table triggers: 0 - BField, 1 - Timer (20 ns step)
• bit 15 - enable counter instead of real adc data

Reg 0x70 - 64bit NCU TIME_STAMP register, 10ns step, RO

Reg 0x74 - 64bit END_RUN TIME_STAMP register, 10ns step, RO

Reg 0x78 - 64bit current TIME_STAMP register, 10ns step, RO

Reg 0x7C - 32bit current BField, RO

Reg 0x80 ... 0x9F - 16 x 32-bit Table Triggers registers, R/W

Reg 0x100 ..0x10F - 16 x 16-bit registers: statistics, clear by NCU, RO (TODO)

BPM4100 MLinkRegisters